- Defender Series
- Commuter Series
- Symmetry Series
- Otterbox for iPad
Otterboxes are some of the near durable smartphone and tablet cases y’all can buy—but that same durability can go far difficult to remove from your device. If you know which type of example you have, y’all can employ different tips and tricks to pry them off carefully without damaging your telephone or tablet. With a little bit of patience and some elbow grease, you lot can get your case off quickly without a ton of frustration.
Remove the snap-on holster.
If the device is in a belt clip or other snap-on attachment, popular information technology off using the big tab on the side. This will get in much easier to take the rest of the example off, so it’due south best to practice it correct away.
- The procedure for removing a Defender Otterbox example will be the same for virtually all devices (iPhone, Android, etc.). The just differences volition be the number and the manner of tension clips.
Detect an opening in the silicone slipcover.
The most difficult part of removing the Defender instance is peeling off the flexible silicone layer. Your best bet is to start at the camera opening, the charging port, or a corner of the screen.[ii]
- The silicone embrace is the flexible outer layer of the example, non the hard plastic within.
Wedge a thin tool or your finger under the embrace.
Employ the tip of your finger to pry the silicone cover away from your phone. If yous tin’t fit your finger into one of these openings, employ an old credit card or a coin to help you out. Stick it underneath the slipcover, and jerk it back and along until you tin can insert your finger into the gap.[iii]
- Make sure you’re not using a credit card you nonetheless utilize! If you jerk besides hard or likewise fast, your card could accidentally snap.
Skin the silicone off carefully.
In one case y’all’ve wedged a corner open up, you lot should be able to go effectually the phone pulling off the silicone. Be conscientious when removing the silicone from your open ports to avoid trigger-happy any port covers.[four]
Release the tension clips along the edge of the case.
Feel forth the edge of the case and detect the small clips along your telephone. Use your fingers to popular the clips up 1 by one until the 2 sides separate and fall off your device.[v]
- If you lot can’t get your finger under the clip, y’all may demand to use a pocket-size apartment-caput screwdriver or a stiff credit card to get some leverage.
- If you’re using a tool to pry the clips open, elevator towards the front end of the case. Don’t try to pull down, or you may suspension the plastic.
- Some clips may be easier to remove than others, especially when all clips are airtight. If you’re having trouble with ane, move onto a different clip.
Outset at the top of the device.
You’ll take the easiest time removing the plastic office of the case if y’all work from the top of the device. Grab one of the corners on the top edges in a higher place the front photographic camera with the telephone facing toward yous.
Pull the superlative plastic up and off the rubber.
You may take to lift a chip to go the plastic over whatever Power buttons. When yous elevator the plastic top off, the rest of the instance should come off easily.
- If you have whatever problem, endeavour pushing a coin or a credit card underneath the rubber example.
Push the rubber casing off i of the corners with your pollex.
Starting from the corner is the easiest mode to begin removing the safe. The seal volition exist tight, so you’ll demand to push with some force.
Work the rubber casing off of the device.
Be careful with the ports, every bit the condom port covers can tear easily. Once the rubber is off your device, you’re in the clear.
- Try storing your case somewhere information technology won’t collect dust.
Push the case off one of the corners with your pollex.
The Symmetry serial is i of Otterbox’s simplest cases: a flexible silicone enclosure for your telephone. The seal is tight, so yous’ll have the best luck starting from a corner and pushing the case off the edge.
- Otterbox recommends starting at the top edge.
Apply a difficult plastic card if necessary.
Wedge the card under an border of the flexible case. Lever it back and forth to pry the example abroad from the device enough to grasp it with your finger.[eleven]
- You tin try this if using your hands doesn’t work.
Work your way around the example.
Once you have a corner off, yous can work your way effectually the edge of the case to remove it. Be careful with the port covers and so that they don’t get torn.
Open up the iPad case.
Yous can do this by flipping it open like you would to use your iPad. Spread the instance out flat then that it’s easier to work with.
- If you have a keyboard connected to your iPad, pop that off start before you start.
Printing downwardly on i lesser corner.
This will commencement to remove the case from the edges of your iPad. As you press down, try to pull your iPad up by the corner at the aforementioned time.
- If yous’re having trouble, try sticking a coin in between the example and the iPad.
Pull your iPad up and out of the instance.
Once you have i corner free, pull your iPad upwardly and away from the case. If any of the corners get stuck, carefully jerk them out before you keep lifting.
Add together New Question
Do y’all demand to remove the plastic embrace from the front of the otterbox case?
Some models accept a screen embrace built into the case, while others have a plastic canvas that attaches direct to the screen earlier the case is installed. Either way, you lot do not demand to remove the comprehend to open the otterbox case.
How practise I remove an Otterbox from my iPhone 6?
On the side, there should be a squeeze or something to detach the two part of the telephone case. Next, you tin use your nails or anything strong and thin (like a credit menu) to take them apart.
How do I open up the Otter Box for an HTC Desire Eye?
This is i of the Defender cases described above. Information technology helps to have a hard plastic carte du jour to wedge under the flexible cover. If the snaps on the hard inner shell won’t open, you can carefully pry them apart with a butter knife or apartment head screwdriver.
See more answers
Ask a Question
200 characters left
Include your email accost to get a message when this question is answered.
Some Otterbox cases come with a hard plastic tool to help yous wedge open the ii halves of the case. This tool is designed to slip onto the lanyard on your case. If you don’t have this tool, a hard plastic library menu or similar tool should work.
Thanks for submitting a tip for review!
Most This Article
To open an Otterbox Example for the Defender Series, start by popping the snap-on holster off using the large tab on the side. Once the holster is off, find an opening in the silicone slipcover near the camera opening, charging port, or a corner of the screen. If you lot tin can’t fit your fingers into whatsoever of the openings, use an old credit card or other hard, flexible piece of plastic to sideslip under the cover. Wiggle your credit carte under the plastic until you can fit a finger into the gap. After yous wedge a corner open, start prying off the silicone. When the silicone is off, find the tension clips along the edge of the case, and pop them open with your fingers. Go along to release the tension clips until the ii halves separate.
To learn how to remove an Otterbox Case from an iPad, go on reading!
Did this summary help you?
Thanks to all authors for creating a page that has been read 780,731 times.
Is this commodity upwards to date?